Hey guys,
This pertains to anyone with a SCT tuner going in for the new TSB 7-10-12.
First Return your ST to the base stock tune from the Program vehicle menu.
Second Scroll down to the " DTC Data menu" and press select. Then scroll down to " Read Strategy" and press...
Hey guys,
The Waffle house is right in downtown Jasper, basically about a mile past Walmart in the left.
Just to give you guys some general directions from Birmingham, take I-59/20 to exit 124 Highway 78 exit. Go right off the exit and that will put you on Highway 78. Stay on 78...
Hey guys,
I've gotten some responces and questions about hosting a dynoday and I figured I would give you guys some information about it.
Looks as if the date set is March 17th. I normally charge $135 an hour for dynotuning time and dynotime combined with a minimum of one hour...
This is what I'm saying, if you want every little bit of performance spend you money on something else. I have dynosheets on the coil pack and the UDP's, the UDP shows 3-4 rwhp gains and the coil pack shows nothing.
I'm just trying to help point you in the right direction for parts that...
I just got finished dyno testing a Screaming Demon coil pack on a ST and we made ZERO hp.
We first tuned the truck to the optimum settings and then installed the SD coil pack, we made a back to back run and made absolutly nothing. Then we even reinstalled the factory coil pack and did...
99% of the Sport Tracs/Explorers/ranger's have the ports disabled on the rear of the PCM's and when you plug it in it wont even allow the truck to start. This is why I DONT sell chips to anyone with one of these vehicles.
thanks, Doug.
I've tested this throttle body on the new V6 Mustang and it made nothing. Loki is the manufactorer for most other companies out.
This throttle body is only for the Drive by wire vehicles, I dont know if it will work on a new ST but I wouldn't waste the money to find out. On the GT's and...
From what I'm hearing there will be 8000 a year made which is more a year then the entire run of 03-04' Cobras.
This time next year they should be well at MSRP or below. I've tuned one stock and I'll be tuning another Monday with a pulley and intake, made 464rwhp stock with a tune this...
Reply sent! Sorry for the delay this month guys as it's been truly my busiest all year. I started the month with Sema and leaving the office for 4 days, funny story I had to have SCT ship 35 X-cal's to Vegas and I had to ship them from my motel just to keep up. Then once I got back to 200+...
Hey guys,
I ship daily to Cananda and I dont charge any additional for this. I do use UPS Canada standard and I always mark the package as a gift. I dont know if it helps but I do try.
Thanks, Doug.
Here's some pictures of the Orange ST in the Ford booth at Sema. It also had the mach 1 seat covers and some other stuff but it was hard to look inside. They had the hood poped when I got there but closed it before I could make any pictures.
Still, I spoke with a few companies that make...
Hey guys,
That's it for me for the week, I'm heading out the door for Sema so please allow for time for responces to your email once I return home as I promise to get to everyone.
Also to post replys!
Thanks, and if you're gonna be there be sure and look me up, my cell is...
All are great suggestions but use simple 10w30 in the crankcase, that's what the specs say from Yamaha. I ride and race both a YZ125 and YZ250, can't figure out which I like better? Also check and/or clean the air filter under the seat. You are going to play hell getting that carb boot off the...
I'll be there Wednesday-Saturday. Give me a call on my cell 205-471-4597 if you'd like to meet. This will be my first time out so I'm looking for any good recommendations for things to see while I'm there.
Thanks, Doug.
Job 2 ends at 2005.
For now there isn't anything available for the 07's but I'm working on it. The big thing wtih the 07's is it will most likely be like the 05up Mustang's and require tuning to work properly. Yes, K&N makes a kit for the Mustangs and says it doesn't require a tune but...